Table T5. Summary of structural measurements, Hole U1324B.
Unit | Core, section, interval (cm) |
Depth (mbsf) |
Core strike (°) |
Reference dip (°) |
True strike (°) |
Reference dip (°) |
Feature/Remarks |
---|---|---|---|---|---|---|---|
308-U1324B- | |||||||
IB | 6H-2, 53 | 43.83 | 124 | NA | |||
6H-4, 65 | 46.95 | 60 | 90 | 231 | 30SE | Fault | |
6H-5, 105 | 48.85 | 60 | NA | Fault, dip probably same as one above with same strike | |||
7H-3, 25 | 54.56 | Possible fault, sediment disrupted | |||||
7H-6, 60 | 59.41 | 16 | NA | Reverse fault, steep, apparent offset 1 cm | |||
7H-6, 81 | 59.62 | Steep reverse fault, disturbed bedding | |||||
ID | 13H-1, 10–130 | 108.4–109.6 | 70 | 90 | 320 | 20SW | Bedding |
13H-2, 60 | 110.40 | 75 | 90 | 320 | 15SW | Bedding | |
13H-2, 80–92 | 110.6–110.72 | Fault zone, showing some small normal faults (riedel shears?) and some possible low-angle reverse faults | |||||
13H-2, 110 | 110.90 | 70 | 90 | 320 | 20SW | Bedding | |
13H-3, 25–120 | 111.55–112.0 | 70 | 90 | 320 | 20SW | Bedding | |
13H-4, 20 | 113.00 | 70 | 90 | 320 | 20SW | Bedding | |
13H-4, 130 | 114.10 | 66 | 90 | 320 | 24SW | Bedding | |
13H-5, 20 | 114.50 | 70 | 90 | 320 | 20SW | Bedding | |
13H-6, 30 | 114.60 | 70 | 90 | 320 | 20SW | Bedding | |
13H-6, 80 | 116.80 | 75 | 90 | 320 | 15SW | Bedding | |
IE | 15H-2, 5–50 | 128.85–129.3 | Normal faults | ||||
21H-4, 125 | 184.75 | 110 | NA | Reverse fault | |||
22H-1, 25 | 187.15 | 60 | Possible fault | ||||
IF | 32H-1, 40 | 265.00 | 120 | 52NE | 332 | 56NE | Bedding |
32H-2, 125 | 267.34 | 140 | 50NE | 319 | 70NE | Bedding | |
32H-3, 10 | 267.70 | 125 | NA | Bedding | |||
32H-3, 20–150 | 267.8–269.10 | ~155 | NA | Bedding, small reverse faults in this interval | |||
34H-1, 65–100 | 283.15–283.5 | Bedding disrupted | |||||
34H-1, 15 | 284.15 | 150 | 90 | 98 | 60S | Bedding | |
34H-2, 22 | 284.22 | 115 | 90 | 98 | 25S | Bedding | |
34H-4, 40 | 285.90 | 40 | 90 | 98 | 50N | Bedding | |
34H-4, 100 | 288.00 | 90 | 90 | Beds horizontal | |||
IG | 37H-2, 120 | 307.25 | 50 | 58NW | 196 | 75NW | |
39H-2, 90 | 321.60 | Possible fault | |||||
IIB | 57X-1, 25–75 | 445.25–445.75 | Possible slump fold | ||||
58X–59X | 454.6–473.95 | Disruption of layering, mass transport deposit? | |||||
IID | 71X-2, 30 | 581.40 | 65 | 75N | Dipping beds, biscuiting causes reversal of orientations in core on <5 cm interval, cannot be oriented | ||
72X-1, 20–130 | 589.4–590.3 | Deformed zone, possible overturned folds, grain size reversals suggest overturned beds |
Notes: Orientation convention: strike taken on cut core face, measured in a clockwise direction 0°–360°, dip taken from cut core face downward, with direction referred to compass quadrant with north being at top of core. APC cores can be oriented by reference to Tensor tool measurement taken during coring.
Previous | Close | Next | Top of page