Previous | Close | Next
Table T13. Coring-disturbed intervals and gaps, Site U1336. (See table notes.)
Core, section,
interval (cm)
|
Type of
disturbance
|
|
320-U1336A-
|
|
1H-1, 0–31
|
Minor
|
|
2H-1, 0–76
|
Top of core
|
|
3H-1, 0–127
|
Top of core
|
|
4H-1, 0–142
|
Top of core
|
|
5H-1, 0–12
|
Top of core
|
|
6H-1, 0–34
|
Top of core
|
|
10H-1, 0–64
|
Top of core
|
|
11H-1, 0–6
|
Top of core
|
|
12H-1, 0–84
|
Top of core
|
|
12H-7, 8–70
|
Distorted liner
|
|
13H-1, 0–111
|
Top of core
|
|
14H-1, 0–150
|
Slurry
|
|
15H-1, 0–30
|
Top of core
|
|
16H-1, 0–82
|
Top of core
|
|
16H-3, 100–150
|
Slight
|
|
16H-4, 94–150
|
Drilling biscuits
|
|
16H-5, 0–5
|
Drilling biscuits
|
|
16H-5, 5–150
|
Flow-in
|
|
16H-6, 0–127
|
Flow-in
|
|
17H-1, 0–12
|
Top of core
|
|
19H-1, 0–25
|
Top of core
|
|
21H-1, 0–42
|
Top of core
|
|
22X-35X, all sections
|
Drilling biscuits
|
|
320-U1336B-
|
|
2H-1, 0–60
|
Top of core
|
|
2H-1, 85–87
|
Void
|
|
4H-1, 0–25
|
Top of core
|
|
5H-1, 0–5
|
Top of core
|
|
6H-1, 0–50
|
Top of core
|
|
7H-1, 0–55
|
Top of core
|
|
8H-1, 0–60
|
Top of core
|
|
9H-1, 0–130
|
Top of core
|
|
10H-1, 0–10
|
Top of core
|
|
11H-1, 0–20
|
Top of core
|
|
12H-1, 0–20
|
Top of core
|
|
13H-1, 0–10
|
Top of core
|
|
14H-1, 0–10
|
Top of core
|
|
14H-4, 122–150
|
Flow-in
|
|
14H-5, 0–150
|
Flow-in
|
|
14H-6, 0–150
|
Flow-in
|
|
14H-7, 0–end
|
Flow-in
|
|
15H-1, 0–30
|
Top of core
|
|
16H-1, 0–15
|
Top of core
|
|
16H-2, 0–150
|
Disturbed
|
|
17H-1, 0–15
|
Top of core
|
|
18H-1, 0–20
|
Top of core
|
|
19H-1, 0–10
|
Top of core
|
|
20H-1, 0–10
|
Top of core
|
|
20H-7, 20–end
|
Deformed liner
|
Notes: When interval listed is 0–150 cm, entire section is included even if true section length is <150 cm. Top of core = myriad forms of voids, disturbance, and debris from uphole that affect top portion of most cores. For that reason, probably the top 20 cm or so of all cores should be avoided.
Previous | Close | Next | Top of page